Kiloview Decoder

This module controls Kiloview Dxx decoders with decoder-hi3536 firmware via its native HTTP API (/api/* on port 80).

Configuration

• Device IP / Host — IP address of the decoder
• Protocol — HTTP (decoder-hi3536 listens on port 80)
• Port — Default 80
• Use Authentication — Enable/disable login credentials
• Username / Password — Device login credentials (default: admin/admin)
• Enable Polling — Required for feedbacks and variables to update automatically
• Polling Rates — Intervals for device state and source list polling
• Verbose Logging — Enable debug-level logging

Actions

System

• Refresh Device Status — Manually refresh outputs, layouts, preview, and device info
• Reboot Device — Reboot the decoder
• Restore Factory Settings — Restore factory defaults

Layout

• Select Layout — Apply a layout template to Output 1 or Output 2 (Output & Layout)
• Select Layout and Assign Source — Switch layout, then assign a stream to a position
• Save Layout — Save current output changes to a layout preset (Output & Layout)
• Reload Layout — Reload layout from saved preset (discards unsaved changes)

Output & Source

• Assign Source to Position — Bind a stream to Output 1/2 window position (starts playback)
• Remove Source from Position — Clear a stream from a window position
• Set Output Resolution — Change output timing/resolution
• Set Position Mute — Mute or unmute audio on a position
• Start Stream Playback / Stop Stream Playback — Control stream decode
• Refresh Source List — Trigger source/NDI discovery refresh
• Add Source Stream — Add RTSP/RTMP/HTTP/HTTPS/UDP stream to a group
• Add NDI Source — Add an NDI stream to a group
• Modify Source Stream — Update name, URL, or credentials of an existing stream
• Remove Source Stream — Delete a stream from a source group

Video Output (HDMI/SDI)

• Toggle Video Interface — Turn HDMI1, HDMI2, or SDI video on/off
• Set Video Interface Enable — Explicit on/off
• Set Video Interface Mode — Set HDMI or DVI mode on HDMI1/HDMI2
• Set Video Interface Colorspace — Set RGB444/YCBCR colorspace on HDMI/SDI

Audio Output (HDMI/SDI/Line Out)

• Toggle Audio Interface — Turn HDMI1, HDMI2, SDI, or Line Out audio on/off
• Set Audio Interface Enable — Explicit on/off
• Set Audio Interface Mute — Mute on/off per output interface (Output + Interface + Mute On/Off)
• Set Audio Interface Volume — Volume in dB (-51 to 20)

NDI Discovery

• NDI: Add Manual IP — Add manual NDI discovery IP and group
• NDI: Add Discovery Server — Add NDI discovery server address

Preview

• Assign Source to Preview — Add a stream to the preview panel
• Remove Preview Source — Remove a stream from a preview slot

Audiomix

• Set Audiomix Enable — Enable/disable a stream in output or preview mix
• Set Audiomix Volume — Set mix volume in dB (-51 to 20)

PTZ (NDI sources only)

• PTZ: Store Preset — Store current PTZ position (preset 0–99)
• PTZ: Recall Preset — Recall a stored PTZ preset with speed

Feedbacks

• Output Layout Active — Layout is active on an output
• Output Layout Modified — Output has unsaved layout changes
• Position Stream Connected / Stream Name Match — Output window stream state
• Output Resolution Match — Output resolution matches selection
• Preview Stream Connected / Stream Match — Preview panel stream state
• Audiomix Stream Enabled — Stream enabled in audiomix panel
• Video Interface Enabled — HDMI/SDI video interface is on
• Audio Interface Enabled — HDMI/SDI/Line Out audio interface is on
• Audio Interface Muted — Audio output interface is muted

Variables

• Device info: name, firmware, hardware, serial, software version
• Per-output: name, layout, resolution, modified flag
• Per-position: stream name, status, resolution
• Per-preview-slot: stream name, status

Presets

Presets are grouped hierarchically by output:

• Output 1 / Output 2
  • Layout — layout switch and save
  • Video — HDMI1/HDMI2/SDI toggle, HDMI/DVI mode
  • Audio — HDMI1/HDMI2/SDI/Line Out toggle and mute
  • Sources — assign streams to window positions
• Device
  • Sources — refresh, NDI discovery, start/stop/remove streams
  • PTZ — recall presets 0–3
  • System — refresh status, reboot

API Reference

Implemented against decoder-hi3536 (RegistHttpsRoute.cpp). Base URL:

http://<ip>:80/api/

See also decoder-hi3536/api/Dxx解码器Api文档.md.