Loading...
Loading...
Tested on a Roland V-80HD with firmware v1.20.201. Every action and feedback has been tested on hardware.
State polling is fixed at 500ms, and each address is requested individually — the device does not answer batched requests.
The device answers only about 58% of those polls. That is measured on hardware with no packet loss, so it is the unit's behaviour rather than a network fault. Most feedbacks still update within half a second; the gap between readings of a given value reaches 5 seconds at the 99th percentile and 6.5 at worst.
In practice this is invisible for steady states — sources, mutes, on-air flags — because the next reading corrects anything missed. It matters for brief events: a one-second fade can pass entirely between two readings of the same address.
Polling is always on. It is the only way the module reads state back from the device, which pushes nothing unprompted, so there is no setting to turn it off. Utility – Sync state now reads everything once, immediately, without waiting for the next poll.
A connection watchdog runs every second and recovers the link automatically:
This covers silent network loss, where the socket remains open but the device is no longer reachable. If the module still does not reconnect, disable and re-enable it in Companion.
The V-80HD applies a brute-force lockout after repeated failed password attempts, and will reject even the correct password while that lockout is active. So the module never retries a password on its own. If the device rejects the password or reports the lockout, the module closes the connection and shows the reason in the connection status. It stays stopped until you save the connection config, or disable and re-enable the connection. After a lockout, wait for the device to clear it first.
Set AUX 1 and AUX 2 Source — full source list
Set AUX Linked PGM (Off, Auto Link, Manual Link) — this sets the link mode and is global
Set AUX Linked PGM bus follow — chooses whether AUX 1 or AUX 2 follows PGM, and Toggle for the same
Set AUX Layer – PinP & Key — Disable, Enable, Always On, per layer per bus
Toggle AUX Layer – PinP & Key between Disable and Enable
Toggle AUX Layer – PinP & Key between Disable and Always On
Split 1 is the vertical split; Split 2 is the horizontal split. Confirmed against the panel on 2026-09-16. The device numbers them rather than naming them, so the orientation is carried in the action names here.
View Position H and V only show their effect once View Zoom is raised. At the default 100% zoom the travel over the -50 to +50 span is too small to see, which is why these were recorded as "not working" through two test sessions. Raise View Zoom first and the movement is obvious. Confirmed on hardware 2026-09-15.
Everything in this section works, including Window Position. If a View Position button appears to do nothing, check the zoom before anything else.
This may start a livestream, not just a recording. On the V-80HD the livestream, audio recording and video recording all start and stop together and cannot be triggered separately. Which of them actually happens is set on the unit under Menu, Stream&Record, using the Live Streaming, Video Rec and Audio Rec settings. Those are device settings and cannot be changed from Companion.
So if Live Streaming is enabled on the unit, Start begins a livestream. The V-80HD streams RTMP and RTMPS to YouTube Live, Facebook Live and Twitch, plus custom RTMP destinations, and SRT to other devices. Check the unit's Stream&Record settings before you assign this to a button.
The device reports its own Stream & Record state, so the feedback is accurate no matter what started it — Companion, the front panel, or the Roland RCS software. Four states are reported: Stopped, Starting, Running and Stopping. Starting and Stopping are brief and may be missed between polls.
These actions were called Record in earlier versions. Existing buttons are migrated automatically.
Capture Image to Still is the only capture action. It opens the capture screen, takes the still and closes the screen again by itself, so there is nothing to drive by hand.
The target slot is overwritten without confirmation. There is no undo.
The button returns straight away. The still is written in about a second, and the capture screen then clears itself roughly seven seconds later with nothing further from you. There is no button to press on the unit.
That seven-second wait is deliberate and cannot be shortened. Capture mode leaves its screen up on the monitor, and the unit needs far longer than its own "capture done" reply suggests before it will accept the press that dismisses it. Shorter waits were tried and broke the capture outright.
One capture at a time, 10 seconds apart. A second capture sent while the first is still finishing can freeze the V-80HD in capture mode, and only a power cycle recovers it. So for 10 seconds after a capture starts, any further capture press is ignored — nothing is sent to the unit — and a warning is logged. The Image Capture – wait feedback shows WAIT ! on the button when that happens, until the 10 seconds are up. The Image Capture presets carry it already; add it by hand to capture buttons built with an earlier version.
If the connection drops or the connection config is saved while a capture is running, the module stops the capture rather than pressing buttons on the new connection, and logs a warning. Check the still, and close the capture screen on the unit if it was left open before capturing again.
There is a matching preset in its own Advanced preset category. It ships with an empty command string, so fill the command in on the button after dropping it on a page. It is kept in a category of its own so it is not picked up by accident while browsing the ordinary presets.
Several actions carry a fuller note or warning that appears once the action is on a button, above its options — Send raw LAN command, Capture Image to Still, Stream & Record Start and Stop, Test Pattern, and the two AUX Linked PGM actions. The ones that can do something you cannot take back — Send raw LAN command, Capture Image to Still, and Stream & Record Start and Stop — also show a one-line warning in the action list, before you pick them.
The following states are polled and drive feedbacks:
One feedback is not polled: Image Capture – wait shows WAIT ! when a capture press is ignored because the previous capture is still finishing. See Image Capture above.
Use engaged for an FTB button. It lights for as long as the output is black, however that happened — from Companion, the V-80's panel, or the Roland RCS software. Fade in progress lights only during the one-second transition, which is why a button using it alone appears to flash and then go dark while the output is still black.
The FTB preset in the Transitions category carries both, so a button dropped from it shows the transition and then stays lit. Buttons built from an older preset do not update themselves — presets are copied when dropped rather than linked — so add the engaged feedback by hand or drop a fresh one.
Stream & Record state is polled with everything else. The device reports it on 030800, but it
pushes that status only to the Roland RCS session, never to this one, so the module asks for it on
every cycle. The value still comes from the device's own report rather than from what the module
sent, so the feedback stays correct whether the stream was started from Companion, the front panel
or RCS.
Two separate settings, and both must be right for anything to happen.
Mode (global): Off, Auto Link or Manual Link. Off means no AUX link at all.
Per-bus follow (AUX 1 and AUX 2): whether that bus follows PGM.
The mode gates the per-bus settings. With the mode set to Off, the follow buttons do nothing — set the mode to Auto Link or Manual Link first.
Auto Link and Manual Link behave identically while the link is intact. They differ only in how the link is restored after you break it, which you do in either mode by selecting an AUX source by hand:
This matters when driving AUX from Companion. Under Auto Link, a Set AUX Source action is temporary — the next CUT or AUTO undoes it. Under Manual Link it persists. If your buttons set AUX sources directly, Manual Link is usually the mode you want.
Tally PGM and Tally PST report which inputs the switcher itself says are on air. They read a state register over the same LAN connection everything else uses, so they need nothing plugged into the unit's tally port and work on a switcher with no tally hardware attached at all.
This is not the same as the Program feedbacks. Program reports which source is selected on the PGM bus; tally reports what the switcher considers on air. Prefer tally when a source can reach air through a PinP or DSK layer rather than the bus, and for direct HDMI and SDI sources, which the Input 1 to 8 feedbacks deliberately do not light for.
The following variables are available for use in button labels and expressions:
| Variable | Description |
|---|---|
| program_input | Active program input number |
| preview_input | Active preview input number |
| program_source | Program source byte in hex |
| preview_source | Preview source byte in hex |
| aux1_input | AUX 1 active input number |
| aux2_input | AUX 2 active input number |
| aux1_source | AUX 1 source byte in hex |
| aux2_source | AUX 2 source byte in hex |
| transition_type | MIX or WIPE |
| mix_time | Transition time in milliseconds |
| wipe_type | Active wipe pattern name |
| wipe_direction | Wipe direction name |
| pinp1_pgm | PinP 1 PGM state (ON or OFF) |
| pinp1_pvw | PinP 1 PVW state (ON or OFF) |
| pinp2_pgm | PinP 2 PGM state (ON or OFF) |
| pinp2_pvw | PinP 2 PVW state (ON or OFF) |
| dsk_pgm | DSK PGM state (ON or OFF) |
| dsk_pvw | DSK PVW state (ON or OFF) |
| split1 | Split 1 Vertical state (ON or OFF) |
| split2 | Split 2 Horizontal state (ON or OFF) |
| aux_linked_pgm | AUX Linked PGM mode |
| aux1_linked_pgm | AUX 1 follows PGM (ON or OFF) |
| aux2_linked_pgm | AUX 2 follows PGM (ON or OFF) |
| main_bus_mute | Main bus mute state (ON or OFF) |
| aux1_bus_mute | AUX 1 bus mute state (ON or OFF) |
| aux2_bus_mute | AUX 2 bus mute state (ON or OFF) |
| ftb | ENGAGED, CLEAR or UNKNOWN |
| ftb_fading | Fade in progress (ON or OFF) |
| freeze | Global freeze state (ON or OFF) |
| test_pattern | Active test pattern name |
| stream_record | Stream & Record active (ON/OFF) |
| stream_record_state | Stopped, Starting, Running or Stopping |
Per-channel audio mute variables. Each reports ON or OFF:
| Variable | Channel |
|---|---|
| mute_audio_in_1 | Audio In 1 |
| mute_audio_in_2 | Audio In 2 |
| mute_audio_in_34 | Audio In 3/4 |
| mute_usb_in | USB In |
| mute_bluetooth_in | Bluetooth In |
| mute_audio_player | Audio Player |
| mute_hdmi_in_1 to mute_hdmi_in_4 | HDMI In 1 to 4 |
| mute_sdi_in_1 to mute_sdi_in_4 | SDI In 1 to 4 |
| mute_video_player | Video Player |
Per-input freeze variables. Each reports ON or OFF:
| Variable | Input |
|---|---|
| freeze_hdmi_1 to freeze_hdmi_4 | HDMI 1 to 4 |
| freeze_sdi_1 to freeze_sdi_4 | SDI 1 to 4 |
Tally variables. Each reports OFF, PGM or PST:
| Variable | Input |
|---|---|
| tally_hdmi_1 to tally_hdmi_4 | HDMI 1 to 4 |
| tally_sdi_1 to tally_sdi_4 | SDI 1 to 4 |
Variables are accessed as $(instance_label:variable_id), for example $(v80hd:program_input).
0A0800), so Stream & Record Start begins whichever of Live Streaming, Video Rec and Audio Rec are enabled in the unit's menu.Module shows as disconnected — check the IP address, confirm port 8023, and ensure a network password has been set on the device via Menu, Network, Network Password.
Module reports authentication failed — the device rejected the password. Correct it in the connection config and save; the module does not retry a rejected password by itself.
Module reports a device auth lockout — the V-80HD has locked out after repeated failed password attempts and will reject even a correct password until it clears. Confirm the password matches the one set on the device, wait for the lockout to clear, then disable and re-enable the connection.
Feedbacks not updating — allow a few seconds rather than half a second, since the device does not answer every poll. If feedbacks remain static after that, disable and re-enable the connection.
AUX routing not responding as expected — AUX Linked PGM is probably overriding it. Under Auto Link, the next CUT or AUTO puts AUX back to following PGM. For AUX selections that stick, set the mode to Manual Link or Off. See AUX Linked PGM above.
PinP appearing on the wrong output — use the AUX Layer – PinP & Key actions to control PinP on the AUX bus independently. The PinP PGM Toggle action affects the main program output layer only.
Roland
CommunityRoland
CommunityRoland
CommunityRoland
CommunityRoland
CommunityRoland
Community