Meyer Sound Galaxy — Module Help
Unofficial Bitfocus Companion module for Meyer Sound Galaxy processors.
Control your Meyer Sound Galaxy processors with real-time control, variables, and feedback for inputs, outputs, matrices, snapshots, hardware status, and more.
Compatibility
| Device | Status |
|---|
| Galaxy 816, Galaxy Virtual | Tested |
| Galaxy 408, Galaxy 816 AES | Should work |
| Bluehorn | Partial support (some differences may require testing) |
| Galileo, Callisto | Not compatible |
Firmware: Galaxy firmware 2.9.1 or newer required.
Setup
- In Companion, add the Meyer Sound Galaxy module.
- Configure the connection settings:
- IP Address — the IP address of your Galaxy processor
- Port — default is
25003
- The module will automatically subscribe to all inputs, outputs, matrices, clocks, and status channels.
- Variables, feedbacks, and presets are instantly available.
Auto-discovery on Linux and Raspberry Pi (Companion Pi)
The Galaxy to control list is filled by a small native helper that listens for the Galaxy's MILAN (ATDECC) announcements on the LAN. On Linux that requires raw network access. Companion Pi runs Companion as the unprivileged companion user, so after installing or updating this module grant the helper that single capability once:
sudo setcap cap_net_raw=eip /path/to/the/module/prebuilt/galaxy-discovery-helper-linux-arm64
Then disable and re-enable the connection. If the capability is missing, the connection log shows a "permission denied opening AF_PACKET socket" message followed by the exact command to run (with the real path). Everything else keeps working in the meantime: type the Galaxy's address into IPv4 / IPv6 / mDNS address and the module connects directly. The Linux helper binaries are statically linked, so they run unchanged on Raspberry Pi OS Bullseye and Bookworm (64-bit).
Features
Speaker Test
Cycles through outputs automatically for quick speaker line testing. Supports solo or paired (A+B) modes with adjustable timing. Outputs are muted/unmuted automatically during the sequence.
Line Array Design
Configure multiple outputs for line array deployments with a single action:
- Select loudspeaker model (LEO-M, LYON, LEOPARD, MICA, PANTHER, MINA, LINA, etc.)
- Set number of elements and elements per output
- Phase curve selection per loudspeaker type
- Mixed array support with automatic delay compensation
- Optional starting point presets
- Output link group assignment with automatic enable
- Channel naming with custom prefix
- LMBC (Low-Mid Beam Control) configuration with beam angle, control type, and array assignment
Subwoofer Design Assist
Five deployment modes for subwoofer configurations:
- End-Fire — Calculate and apply progressive delay taps based on target frequency and air temperature (2–8 taps, with recommended spacing preview). Pick a loudspeaker and its phase curve (PC63/PC100/PC125, as available); the Front Facing starting point is applied automatically. Choose the first output and the remaining taps auto-fill one output per tap (T0 = first, T1 = first+1, …). Loudspeakers without a front-facing preset accept a manual base delay added on top of every tap.
- Array — Configure arc/curved arrays with delay timing based on sub spacing, arc angle, and temperature. Automatic symmetric delay calculation.
- Array End-Fire — Combines end-fire rows with arc configuration for multi-row deployments.
- Array Gradient — A symmetric arc of front-facing subs (like Array) plus one rear-facing sub per front sub for a cardioid arc. Pick the front and rear starting outputs; each rear sub gets its front partner's arc delay plus the cabinet gradient delay with polarity reversed (front/rear presets and phase curve are chosen automatically; loudspeakers without a rear preset accept a manual rear delay). Supports the same Mono/Stereo and flip-layout options as Array.
- Gradient — Apply gradient subwoofer presets with front and reversed polarity outputs.
- End-Fire Gradient — Combines gradient and end-fire. Pick a loudspeaker, its phase curve (PC63 / PC100 / PC125, as available), the number of end-fire taps, and the first front-facing and first rear-facing output; the remaining outputs are filled in automatically. Adjacent first outputs (e.g. front 1, rear 2) interleave the pairs (1,3,5… front / 2,4,6… rear); a larger gap lays them out as consecutive blocks (e.g. front 1, rear 5 with 4 taps → 1–4 front / 5–8 rear). The correct front/rear starting point is chosen automatically per loudspeaker. Each tap's end-fire delay (from target frequency and air temperature) is added on top of the cabinet gradient delay carried by the rear-facing outputs; front-facing outputs receive the end-fire delay only. Loudspeakers without a factory rear-facing preset accept a manual rear delay, with polarity reversed automatically. An optional channel-name prefix names each output "<prefix> T# Front" / "<prefix> T# Rear".
All modes support loudspeaker selection for product integration, starting points, output link group assignment, and optional factory reset before applying settings. Each mode also accepts an optional channel-name prefix (e.g. "Sub") that names the configured outputs with a role/position suffix, and selecting an Output Link Group automatically enables it (choose "None" to leave link groups untouched). A Status line shows standby, the applied summary, or — for an impossible layout — the reason and how to fix it (nothing is applied in that case).
Speed of Sound / Spacing Calculator
A standalone action with no effect on the Galaxy. Enter air temperature and a target frequency, press the button, and it reports the speed of sound and the recommended ¼-wavelength sub spacing (m and ft) in its Result line.
Inputs
- Mute, unmute, toggle
- Set, nudge, or fade gain (dB)
- Parametric EQ control with fine/coarse modes
- Link group assignment and bypass
- Variables for name, mute state, and gain
- Feedback for mute status and gain levels
Outputs
- Mute, unmute, toggle
- Set, nudge, or fade gain (dB)
- Parametric EQ control with fine/coarse modes
- Link group assignment and bypass
- Line array design tools
- Factory reset per channel
- Variables for name, mute state, and gain
- Feedback for mute status and gain levels
Matrix
- Select multiple inputs and outputs simultaneously
- Set, nudge, or fade crosspoint gains
- Variables and feedback for all crosspoints
Snapshots
- Recall snapshots (0–255)
- Variables for active snapshot (ID, name, timestamps)
- Feedback for snapshot state
Presets
- Auto-generated mute buttons for inputs and outputs
- Labels display channel number, name, and gain
- Feedback coloring (red when muted)
Linking Galaxies (Link ID)
Give two or more connections on the same Companion server the same non-empty Link ID (in the connection config) to operate them as one. Any control change you make through a Companion action on one linked Galaxy is automatically replayed on the others — e.g. muting "Galaxy Left" also mutes "Galaxy Right". Leave the Link ID blank to disable linking. Per-unit/identity actions (Identify, Access Lock, Front Panel Lockout, Reboot, Group Name, Clear Log) are intentionally not mirrored. Linking covers connections on the same machine; changes made directly on a device's front panel are not mirrored.
Use the Linking: Enable / Disable action to temporarily suspend mirroring for one connection — handy when you need to adjust a single Galaxy without affecting its linked peers. The link_active variable and the Linking: Active feedback show the current state; it resets to enabled on restart or when the Link ID changes.
Front Panel Lockout
- Lock/unlock Galaxy hardware front panel
- Feedback shows live state
Status & System Info
- Device info (model, firmware, serial, group name)
- Clock & sync (AES, word clock, system clock)
- Network status (IP, MAC, speed)
- RTC date & time
Variables
| Variable | Description |
|---|
$(Galaxy:input_1_name) | Input 1 name |
$(Galaxy:input_1_gain_db) | Input 1 gain in dB |
$(Galaxy:input_1_mute) | Input 1 mute state (true/false) |
$(Galaxy:output_3_name) | Output 3 name |
$(Galaxy:snapshot_active_id) | Currently active snapshot ID |
Feedbacks
- Input/output mute status (visual indicator when muted)
- Gain threshold comparisons (equal, above, below target dB)
- Matrix crosspoint gain monitoring
- Front panel lock state
Notes
This is a community-driven, unofficial module. Use at your own risk.
Feature requests and bug reports are welcome via GitHub Issues.